Eagle Sea Speed SPC

Overview

Eagle Sea Speed SPC LRA (Long Range Activity) is a low friction, self-polishing SPC antifouling with a high solid content and copolymer tin-free technology for outstanding performance. A high strength A/F technology is designed for 5 years service period under heavy fouling and static conditions. Very stable self-polishing mechanism, tin-free A/F is certified to comply with IMO Antifouling System Convention (AFS/CONF/26). Eagle Sea Speed SPC can also be applied on navy vessels, coastal cruisers and deep sea ocean vessels, where longer static conditions arise. Expected service life ranges from a minimum of 36 months and up to 60 months. Eagle Sea Speed SPC displays excellent compatibility with various well known producers.

Purpose

To be used on Vessels operating on worldwide trading service with dry docking intervals up to 60 months. Can be applied for newbuilding, and maintenance and repair. Suitable protection on hull under all fouling conditions.

Properties

Sheen: Matte

Color: Light Red, Redbrown, Black, Blue

Solids: 63 ± 2

Coverage: 6.20 m2/Lit at 100 microns dry

Thickness: 75-175 microns dry

Flashpoint: 28 2 °C

VOC: 364.00 g/Lit (material as into the container), Density: 1.76 kg/Lit

Application Data

Mixing Ratio: Single pack product which should be stirred well before application by stirring machine.

Thinner: Not recommended. The material is ready for use, under special conditions use Thinner PH 400, max 5% by volume.

Painting Method: Airless spraying is our recommendation, brush, and spray follows. Tip range 0.46mm-0.66mm and 0.66-0.79, blowing pressure shouldn’t be less than 141kg/cm2 (2000psi). May be required to add thinner. Use the proper equipment. Actual safety measures and precautions are very important for the selected method and environment work. Emergency Contact Numbers are available World Wide upon any request.

Cleaning: Power tool cleaning with Thinner PH 400.

Drying and Over-Coating Conditions

Eagle Sea Speed SPC.JPG

Coating Specification

A/F Eagle Sea Speed SPC should always be applied to a recommended coating system. The surface should be dry and free from contamination on any existing layers of PhilaDur line, Phila VIN/CL, link coat/sealers or various A/Fs, in order to secure good adhesion and good A/F performance. Specific recommendations and statements, as there is a Limit liability only for the supplied quantity and value of the A/F, should be agreed and approved by Philadelphia Coatings LLC Technical Department, in writing to do so.

Surface Preparation

All surfaces should be clean, dry and free from contamination. High pressure or pressure with fresh water wash should be applied prior to the treatment or of the application. For other surface treatments, please consult with Philadelphia Coatings LLC.

Storage

Circa 24 months at 20°C, stored at dry, shaded and ventilated condition. The container/paint, must be kept sealed and away from heat and ignition.

Pack Size

Standard packing of 5,3 Gal. (20 Lit) pail. If other packing specifications are needed, please consult with Philadelphia Coatings LLC.

Health and Safety

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.

Limitation of liability

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Philadelphia Coatings LLC. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, soPhiladelphia Coatings LLC won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.

Disclaimer

The information in the product manual is based on our experiences from tests and practice. For the application without our knowledge, we could only make sure that our products themselves are warranted. We may modify the data in this product manual according to our continuous development and experience accumulation without advanced notice.