Eagle Sea Speed SPC Advanced
Eagle Sea Speed tin-free SPC is an advanced, hybrid, low-friction, self-polishing Silyl SPC antifouling. Its high performance technology is comprised of high solids with the insoluble modified acrylate polymer, Copper Cu2-SiR3 (Pyrithion). With its high strength A/F technology, Eagle Sea Speed Advanced is designed for vessels with a 5 year service period undergoing heavy fouling, long-range service, and travelling at medium speed. It is a tin-free A/F certified to comply with IMO Antifouling System Convention (AFS/CONF/26). A/F “Eagle Sea Speed SPC” Advanced can also be applied on navy vessels, coastal cruisers and deep sea ocean vessels, where longer static conditions arise. Expected service life ranges from 60 up to 90 months, providing excellent performance and substantial savings to the operators. It displays very good compatibility with various well known producers.
To be used on higher speed and wide range vessels operating on a worldwide trading service. Focus is on maintaining speed and schedule. For application at new building or maintenance and suitable protection on hull under all fouling conditions. It is highly durable with up to 90 months of service.
Color: Light Red, Redbrown, Black, Blue
Solids: 59 ± 2
Coverage: 5.90 m2/Lit at 100 microns dry
Thickness: 75-175 microns dry
Flashpoint: 26 ± 2 °C
VOC: 390.00 g/Lit (material as into the container), Density: 1.76 kg/Lit
Mixing Ratio: Single pack product which should be stirred well before application by stirring machine.
Thinner: Not recommended. The material is ready for use, under special conditions use Thinner PH 400, max 5% by volume.
Painting Method: Airless spraying is our recommendation, brush, and spray follows. Tip range 0.46mm-0.66mm and 0.66-0.79, blowing pressure shouldn’t be less than 141kg/cm2 (2000psi). May be required to add thinner. Use the proper equipment. Actual safety measures and precautions are very important for the selected method and environment work. Emergency Contact Numbers are available World Wide upon any request.
Cleaning: Power tool cleaning and Cleaners with Thinner PH 400.
Drying and Over-Coating Conditions
A/F Eagle Sea Speed tin-free SPC Special should always be applied to a recommended coating system. The surface should be dry and free from contamination on any existing layers of PHILADUR line, PHILA/VIN CL, link coat/sealers or various A/Fs, in order to secure good adhesion and good A/F performance. Specific recommendations and statements should be agreed and approved by Phila Coatings (USA) Inc. Technical Department in writing to do so, as there is a Limit liability only for the supplied quantity and value of the A/F.
All surfaces should be clean, dry and free from contamination. High pressure or pressure with fresh water wash should be applied prior to the treatment or of the application. Aged antifouling with leached layer: Removal by thorough fresh water washing at minimum nozzle pressure 200 bar. Aged antifouling with leached layer: Removal by thorough fresh water washing at minimum nozzle pressure 340 bar. For new building surface treatment, please consult with Phila Coatings (USA) Inc.
Circa 24 months at 20°C, stored at dry, shaded and ventilated condition. The container/paint, must be kept sealed and away from heat and ignition.
Standard packing of 5,3 Gal. (20 Lit) pail. If other packing specifications are needed, please consult with Phila Coatings (USA) Inc.
Health and Safety
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.
Limitation of liability
All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Phila Coatings (USA) Inc. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, so Phila Coatings (USA) Inc. won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.
The information in the product manual is based on our experiences from tests and practice. For the application without our knowledge, we could only make sure that our products themselves are warranted. We may modify the data in this product manual according to our continuous development and experience accumulation without advanced notice.