Fluorescent Luminous Orange PHL 2005 


Alkyd based, day-light reflecting paint, gives intense color impression and high visibility. Fluorescent Luminous Orange PHL 2005 displays very good compatibility with various well known producers. 


For application as a safety marker on selected areas of drilling rigs and platforms, marker buoys, on board ship and lifeboats. For use at newbuilding, maintenance & repair or on board maintenance. 


Sheen: High-Gloss

Color: Fluorescent Luminous Orange

Solids: 55

Coverage: 10.80 m2/Lit at 50 microns dry / 93 microns wet 

Thickness: 50 microns dry

Flashpoint: Mixed product > 33°C (91.4 °F) 

VOC: 370.00 g/Lit (material as into the container)

Application Data

Mixing Ratio: Single pack product which should be stirred well before application by stirring machine.

Thinner: Not recommended. The material is ready for use, under special conditions use Thinner PH 500 or Thinner PH 400, max 5% by volume.

Painting Method: Airless spraying is our recommendation, brush, and spray follows. Tip range 0.48mm-0.53mm (21 thou), blowing pressure should not be less than 141kg / cm2 (2000psi). May be required to add thinner. Use the proper equipment. Actual safety measures and precautions are very important from the selected method and environment work. Emergency Contact Numbers are available World Wide upon request.

Cleaning: Power tool cleaning with Thinner PH 400.

Drying and Over-Coating Conditions

Fluorescent Paint Orange.JPG

Coating Specification

Apply one or more coats of Fluorescent Luminous Orange as specified on well prepared surfaces and undercoat with PhilaPrimo, PhilaLux, Philacric primers and finishes. Existing surfaces should be prepared, cleaned and formed from hard and glossy areas to dull conditions. Check and confirm the compatibility via patch tests and the integrity of the coated film. Spot and stripe coats should always be well prepared with ref. primers. 

Surface Preparation

All surfaces should be clean, dry and free from contamination. High pressure or pressure with fresh water wash should be applied prior to the treatment or of the application.  For other surface treatments, please consult with Philadelphia Coatings LLC Technical Department. 


Circa 18 months at 25°C, stored at dry, shaded and ventilated condition. The container/paint, must be kept sealed and away from heat and ignition.

Pack Size

5 Gal. (18,9 Lit) drum, 20 Lit drum. If other packing specifications are needed, please consult with Philadelphia Coatings LLC.

Health and Safety

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.

Limitation of liability

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Philadelphia Coatings LLC. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, soPhiladelphia Coatings LLC won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.


The information in the product manual is based on our experiences from tests and practice. For the application without our knowledge, we could only make sure that our products themselves are warranted. We may modify the data in this product manual according to our continuous development and experience accumulation without advanced notice.