PhilaCon PHR-C200

Overview

A single component with heat resistance up to 200 ℃. Composed of aluminum and alkyd resin with heat resistant pigments. Excellent adhesion and durability. PhilaCon PHR-C200 displays very good compatibility with various well-known producers.

Purpose

A cosmetic finish, for above sea water areas of new buildings and ship repairs.

Properties

Sheen: Glossy

Color: Aluminum

Solids: 45 ± 2

Coverage: Theoretical Coverage: 18.00 sq. m/Lit at 25 microns dry / 55 microns wet

Thickness: 25 microns dry

Flashpoint: > 42 °C

VOC: 480.00 g/Lit (material as into the container)

Application Data

Mixing Ratio: Single pack product which should be stirred well before application by stirring machine

Thinner: Not recommended. Material is ready for use, under special conditions use Thinner PH 400, max 5% by volume.

Painting Method: Airless spraying is our recommendation, brush, and spray follows. Tip range 0.38mm-0.46mm (21 thou), blowing pressure shouldn’t be less than 150 kg / sq. cm (2100psi). Additional thinner may be required. Use proper equipment. Safety measures and precautions are very important for the selected method and environment. Emergency Contact Numbers are available world wide upon request.

Cleaning: Power tool cleaning and Cleaners with Thinner PH 400.

Drying and Over-Coating Conditions

PhilaCon PHR-C200.JPG

Coating Specification

Apply one or more coats of PhilaLux as specified on well prepared surfaces and undercoat with PhilaPrimo, PhilaClor, or Philacric primers and finishes. The existing surfaces should be brushed and cleaned to turn the hard and glossy areas to smooth conditions. Check and confirm the compatibility via patch tests and the integrity of the coated film. Spot and stripe coats should always be well prepared with aforementioned primers.

Surface Preparation

All surfaces should be clean, dry and free of contamination. High pressure fresh water wash should be applied prior to the treatment or of the application. For other surface treatments, please consult with Phila Coatings (USA) Inc. Technical Department.

Storage

Circa 18 months at 25 °C, stored in a dry, shaded and ventilated condition. The container/paint must be kept sealed and away from heat and ignition.

Pack Size

5 Gal. (18,9 Lit) drum, 20 Lit drum. If other packing specifications are needed, please consult with Phila Coatings (USA) Inc.

Health and Safety

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.

Limitation of liability

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Phila Coatings (USA) Inc. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, so Phila Coatings (USA) Inc. won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.

Disclaimer

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Phila Coatings (USA) Inc. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, so Phila Coatings (USA) Inc. won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.