PhilaDur 06/06 High Solids

Overview

Excellent chemical and mechanical resistance, high solid, two-pack epoxy amine, surface tolerant, excellent abrasion resistance. Specifically formulated for a wide variety of heat sensitive applications, requiring a low substrate temperature during the curing process, from -8°C to atmospheric heat service in marine and industrial environments. In control of solvent emissions (VOC) compliant with EU Solvent Emissions Directive (Council Directive 1999/3/EC.). Abrasion resistance giving excellent long term of anticorrosive protection specifically for immersion / underwater areas, ballast tank, cargo holds, and crude oil tank. Excellent adherence to variety of substrates, such as steel, aluminum, stainless steel, concrete and various pre-coated surface with a broad range of A/C and A/F bottom systems. In application to hydro-blasted surfaces or other well-treated surfaces, needs to be in compliance with various cathodic protection systems and the incidental food contact according to the FDA section 21, chapter 175.300. PhilaDur PHE 06/06 displays very good compatibility with various well-known producers.

Purpose

Providing universal primer performance in harsh environments and protection of steel structures and other offshore navigation. Surface tolerant, and easy to apply.

Properties

Sheen: Glossy

Color: Aluminum, Red Brown, Grey, Green, Black, White

Solids: 82 +/-2

Coverage: Theoretical Coverage: 6.60 sq. m/Lit at 150 microns dry / 179 microns wet

Thickness: Over 250 microns dry by 2 coats.

Flashpoint: Mixed product >27°C

VOC: 217.00 g/Lit (material as into the container)

Application Data

Mixing Ratio: Basis 4 part per/volume, Curing Agent 1 part/volume.

Thinner: Not recommended. The material is ready for use, under special conditions use thinner 400, max 5% by volume.

Painting Method: Airless spraying is recommended, brush and spray follows. Tip range 0.48mm-0.66mm (21 thou), blowing pressure shouldn't be less than 141kg/cm2 (2000psi). Additional thinner may be required. Use the proper equipment. Actual safety measures and precautions are very important from the selected method and environment work. Emergency Contact Numbers are available World Wide upon request.

Cleaning: Power tool cleaning with Universal Thinner PH-400.

Readiness Time: 15 minutes in a proper temperature

Pot Life: 6 hours at 5 °C, 5 hours at 15 °C, 3 hours at 30 °C

Curing Time: Within 4 days at 23 °C (fully cured)

Drying and Over-Coating Conditions

PhilaDur 0606 High Solids.JPG

Coating Specification

Long overcoat period, if local climate, temperatures around to freezing point, proper selection of the systems, coating application procedures, proper surface preparation, as per actual existing film esp. over coated epoxy layer. Try to test design factors, statements and specific recommendations in a controlled laboratory. Always factor in the conditions and consult with Philadelphia Coatings LLC Technical Department before and throughout testing.

Surface Preparation

All surfaces should be clean, dry and free from contamination. High pressure fresh water wash should be applied prior to the treatment of the application. Steel products with mill scale: shot blasting or grit blasting should meet the requirements of Sa1 grade in Sweden derusting standard at least. Steel products without mill scale: to be grinded by dynamic tools to meet the requirements of St3 grade in Sweden derusting standard. Steel products painted with plant primer: use slight grit blasting or dynamic tools to carry out secondary surface preparation to meet the requirements of St3 grade in Sweden derusting standard. For other surface treatments, please consult with Philadelphia Coatings LLC.

Storage

Circa 24 months at 20°C, stored in a dry, shaded and ventilated condition. The container/paint, must be kept sealed and away from heat and ignition.

Pack Size

Basis 4 Gal. (16 Lit) drum, agent 1 Gal (3,785 Lit) drum. If other packing specifications are needed, please consult with Philadelphia Coatings LLC. Shipping weight: Basis 4 Gal. (16 Lit) 65.44 lb drum, agent 1 Gal (3,785 Lit) 4.2 lb drum.

Health and Safety

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.

Limitation of liability

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Philadelphia Coatings LLC. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, so Philadelphia Coatings LLC won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.

Disclaimer

The information in the product manual is based on our experiences from tests and practice. For the application without our knowledge, we could only make sure that our products themselves are warranted. We may modify the data in this product manual according to our continuous development and experience accumulation without advanced notice.