PhilaDur PHE 06/08M

Overview

Excellent mechanical and chemical resistance. It is a high performance, two-component, self-priming polyamide-cured, epoxy product. It forms a tough, hard wearing coating with good resistance to water and petroleum products. Not resistant to aromatic solvents or strong acids. It offers long term protection of steel and other structural materials under severe service and environment conditions. Abrasion resistant. Adheres strongly to steel surfaces, previously painted and galvanized. Is suitable for new construction and maintenance. For durable protection systems with polyurethane and polysiloxane finishes. Excellent barrier protection against corrosion and applicable to a variety of surfaces. Excellent workshop primer for corrosive services. Applicable for immersion service. Meets requirements for organic volatile content. Provides an excellent barrier against corrosion in damaged areas, by the action of its inhibitory pigments. Ensures good behavior in aggressive environments. Better performance than conventional coatings even with manual or mechanical cleaning. Also meets the criteria those for foods contact according to the FDA section 21, chapter 175.300. It is a very good choice where surface preparation is upgraded.

PhilaDur PHE 06/08M displays very good compatibility with various well known producers.

Availability subject to special agreement. Not included in Philadelphia Coatings LLC worldwide Group Assortment.

Purpose

Can be used as a lining or exterior coating on decks, pipes, or according to specification.

Main uses:

• Aluminium

• Carbon steel

• Galvanised steel

• Steel with zinc inorganic

• Concrete

• Non-ferrous metals

• Stainless steel

• Aged coatings

• Floors

• Steel construction

Properties

Sheen: Semi-Gloss

Color: Red Brown, Gray, Green, Blue, Black, White

Solids: 75 ± 2

Coverage: 7.39 m2/Lit at 100 microns dry / 202 microns wet

Thickness: Over 125 microns dry by 1 coat

Flashpoint: Mixed product >23°C

VOC: 280.00g/Lit (material as into the container)

Application Data

Mixing Ratio: For US and Mexico, mixing ratio Basis (A) 14.4 part per/volume, Curing Agent (B) 3.6 part/volume.

Thinner: Not recommended. The material is ready for use, under special conditions use thinner 400, max 5% by volume.

Painting Method: Airless spraying is our recommendation, brush, and spray follows. Tip range 0.48mm-0.66mm (21 thou), blowing pressure shouldn’t be less than 141kg/cm2 (2000psi). May be required to add thinner. Use the proper equipment. Actual safety measures and precautions are very important from the selected method and environment work. Emergency Contact Numbers are available World Wide upon any request.

Cleaning: Power tool cleaning with Universal Thinner PH-400.

Readiness Time: 15 minutes in a proper temperature.

Pot Life: 7 hours at 5°C, 5 hours at 15°C, 3 hours at 30°C

Curing Time: Within 4 days at 23°C (fully cured).

Drying and Over-Coating Conditions

PhilaDur PHE 0608M.JPG

Coating Specification

If local temperatures are around freezing, long overcoat period, the systems, actual existing film esp. over coated epoxy layer, and proper surface preparation, coating application procedures should be selected, and then test in a controlled laboratory. Design factors, statements, specific recommendations should always be valued. Please consult with Philadelphia Coatings LLC Technical Department.

Surface Preparation

All surfaces should be clean, dry and free from contamination. High pressure or pressure with fresh water wash should be applied prior to the treatment or of the application. Steel products with mill scale: shot blasting or grit blasting should meet the requirements of Sa1 grade in Sweden derusting standard at least. Steel products without mill scale: to be grinded by dynamic tools to meet the requirements of St3 grade in Sweden derusting standard. Steel products painted with plant primer: use slight grit blasting or dynamic tools to carry out secondary surface preparation to meet the requirements of St3 grade in Sweden derusting standard. For other surface treatments, please consult with Philadelphia Coatings LLC.

Storage

Circa 18 months at 25°C, stored at dry, shaded and ventilated condition. The container/paint, must be kept sealed and away from heat and ignition.

Pack Size

Basis 3 Gal. (14.4 Lit) drum, curing agent 1 Gal (3.6 Lit) drum. If other packing specifications are needed, please consult with Philadelphia Coatings LLC.

Shipping weight: Basis 3 Gal. (14.4 Lit) drum, curing agent 1 Gal (3.6 Lit) drum.

Health and Safety

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.

Limitation of liability

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Philadelphia Coatings LLC. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, so Philadelphia Coatings LLC won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.

Disclaimer

The information in the product manual is based on our experiences from tests and practice. For the application without our knowledge, we could only make sure that our products themselves are warranted. We may modify the data in this product manual according to our continuous development and experience accumulation without advanced notice.