PhilaDur PHE 06/08SP Smart Pack

Overview

It is a high performance, two-component, amine-cured, epoxy product. It is a surface tolerant, high solids product. Specially designed for application with brush and roller. 1:1 mixing ratio for easy use and reduced wastage. Specially designed for areas where optimum surface preparation is not possible or desired. Provides long lasting protection in environments with high corrosivity. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel, galvanized steel, stainless steel, concrete and a range of aged coating surfaces. PHILADUR PHE 06/08SP Smart Pack display very good compatibility with various well known producers.

Availability subject to special agreement. Not included in Philadelphia Coatings LLC worldwide Group Assortment.

Purpose

General: Primarily designed for smaller maintenance and repair jobs.

Marine: Outside hulls, exterior and interior areas, including water ballast tanks.

Protective: Recommended for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel.

Properties

Sheen: Semi-Gloss

Color: Red Brown, Gray, Green, Blue, Buff, Black, White

Solids: 75 ± 2

Theoretical Coverage: 14.9 - 6.2 m2/Lit dry / 67 - 160 microns wet

Recommended Film Thickness: 50 - 120 microns dry by 1 coat.

Flash Point: Mixed product >33°C

Density: 1.40 kg/lit

VOC: 280.00 kg/Lit (material as into the container)

Application Data

Mixing Ratio: For US and Mexico, mixing ratio Basis (A) 1 part per/volume, Curing Agent (B) 1 part/volume.

Thinner: Not recommended. The material is ready for use, under special conditions use thinner 400, max 5% by volume.

Painting Method: Airless spraying is our recommendation, Brush, Roller follows. Tip range 0.48mm-0.66mm (21 thou), blowing pressure shouldn’t be less than 141kg/cm2 (2000psi). May be required to add thinner. Use the proper equipment. Actual safety measures and precautions are very important from the selected method and environment work. Emergency Contact Numbers are available World Wide upon any request.

Cleaning: Power tool cleaning with Universal Thinner PH-400.

Readiness Time: 15 minutes in a proper temperature.

Pot Life: 1.5 hour at 23°C

Curing Time: Within 7 days at 23°C (fully cured).

Drying and Over-Coating Conditions

PhilaDur PHE 0608SP.JPG

Coating Specification

If local temperatures are around freezing, long overcoat period, the systems, actual existing film esp. over coated epoxy layer, and proper surface preparation, coating application procedures should be selected, and then test in a controlled laboratory. Design factors, statements, specific recommendations should always be valued. Please consult with Philadelphia Coatings LLC Technical Department.

Surface Preparation

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Minimum recommended surface preparation:

Substrate   
Minimum
Recommended
Carbon Steel
St 2 (ISO 8501-1)
Sa 2 (ISO 8501-1)
Stainless Steel
The surface shall be hand or machine abraded with non-metallic abrasives or bonded fiber machine or hand abrasive pads to impart a scratch pattern to the surface and to remove all polish from the surface.
Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface profile.
Galvanized Steel
The surface shall be clean, dry and appear with a rough and dull profile.
Light brush blasting using nonmetallic abrasive leaving a clean, rough and even pattern.
Coated Surfaces
Clean, dry and undamaged compatible coating (ISO 12944-4 6.1.4)
Clean, dry and undamaged compatible coating (ISO 12944-4 6.1.4)
Concrete
Low pressure water washing to a rough, clean, dry and laitance free surface.       
Minimum 4 weeks curing. Moisture content maximum 5 %. Prepare the surface by means of enclosed blast shot or diamond grinding and other appropriate means to abrade the surrounding concrete and to remove laitance.

Optimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. For other surface treatments, please consult with Philadelphia Coatings LLC.

Storage

Circa 24 months at 25°C, stored at dry, shaded and ventilated condition. The container/paint, must be kept sealed and away from heat and ignition.

Pack Size

Basis 2 Gal. (9 Lit) drum, curing agent 2 Gal (9 Lit) drum. If other packing specifications are needed, please consult with Philadelphia Coatings LLC.

Shipping weight

Basis 2 Gal. (9 Lit) drum, curing agent 2 Gal (9 Lit) drum.

Health and Safety

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.

Limitation of liability

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Philadelphia Coatings LLC. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, so Philadelphia Coatings LLC won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.

Disclaimer

The information in the product manual is based on our experiences from tests and practice. For the application without our knowledge, we could only make sure that our products themselves are warranted. We may modify the data in this product manual according to our continuous development and experience accumulation without advanced notice.