PhilaDur Barrier PHE 80 Solvent-Free

Overview

A solvent-free, chemically resistant 2-pack Epoxy coating, for areas above and under water line. Also suitable for reliable protection of ballasts, deck covering of naval ships, helicopter pads, car ferries etc. Can be applied with low treated surface preparation using trowel method of application and leveling up 7000 Microns. High build epoxy filler may be coated over PHILADUR, PHILAFINO, PHILACRIC, PHILATHANE for decorative purposes. Excellent for heavily corroded areas, pitting, anode shields and many other vertical/horizontal steel plates' application. VOC compliant with very limited emissions to the environment. PHILADUR PHE 80 Anti abrasion displays very good compatibility with various well known producers.

Purpose

It is a unique filler for freshwater tank, ballast bank, becks, anode areas, chemical tanks on spot areas and other heavy industrial, offshore construction, oil rigs, etc. Tolerates damp and fresh flash rust areas.

Properties

Sheen: Gloss

Color: Dark Green, Gray

Solids: 99%

Coverage: 3.30 m2/Lit at 300 microns dry / 303 microns wet

Thickness: 300 microns dry

Flashpoint: 27 °C

VOC: N/A

Application Data

Mixing Ratio: Basis 2 part per/volume, Curing Agent 1 part/volume.

Thinner: Not allowed.

Painting Method: Heat up airless spraying is our recommendation, general spraying or brush painting. Airless nuzzle diameter: 0.58mm-0.69mm, blowing pressure shouldn’t be less than 153kg/cm2 (2200psi). Roller and brush: suitable for small area touch up. Actual safety measures and precautions are very important from the selected method and environment work. Emergency Contact Numbers are available World Wide upon any request.

Cleaning: Power tool cleaning and Cleaners with Universal Thinner PH 400.

Readiness Time: 10 minutes in a proper temperature.

Pot Life: 30 minutes

Curing Time: Within 4 days at 23°C (fully cured).

Drying and Over-Coating Conditions

PhilaDur PHE 80 Solvent-Free.JPG

Coating Specification

If local temperatures are around freezing there is a long overcoat period. The systems, actual existing film esp. over coated epoxy layer, proper surface preparation, and coating application procedures should be selected, and then tested in a controlled laboratory. Design factors, statements, specific recommendations should always be valued. Please consult with Phila Coatings (USA) Inc. Technical Department before and throughout the testing process.

Surface Preparation

All surfaces should be clean, dry and free from contamination. High pressure with fresh water wash should be applied prior to the treatment or of the application. Steel products with mill scale: shot blasting or grit blasting should meet the requirements of Sa1 grade in Sweden derusting standard at least. Steel products without mill scale: to be grinded by dynamic tools to meet the requirements of St3 grade in Sweden derusting standard. Steel products painted with plant primer: use slight grit blasting or dynamic tools to carry out secondary surface preparation to meet the requirements of St3 grade in Sweden derusting standard. For other surface treatments, please consult with Phila Coatings (USA) Inc.

Storage

Circa 18 months at 25°C, stored in dry, shaded and ventilated conditions. The container/paint, must be kept sealed and away from heat and ignition.

Pack Size

Basis 4 Gal. (16 Lit) 65.44 lb drum, agent 1 Gal (3,785 Lit) 4.2 lb drum. If other packing specifications are needed, please consult with Phila Coatings (USA) Inc.

Health and Safety

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.

Limitation of liability

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Phila Coatings (USA) Inc. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, so Phila Coatings (USA) Inc. won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.

Disclaimer

The information in the product manual is based on our experiences from tests and practice. For the application without our knowledge, we could only make sure that our products themselves are warranted. We may modify the data in this product manual according to our continuous development and experience accumulation without advanced notice.