PhilaTar PHE 06/05

Overview

An epoxy high built coal tar, surface tolerant, with high solids volume (80%). PHILATAR PH 06/05, is capable of being applied as a one or two coat system over grit blasted, hydroblasted or mechanically cleaned surfaces. It is also tolerant of damp surfaces (see limitation of liability section). Material complies with U.S.A. standards (EPA-Environmental Protecting Agency). PhilaTar PHE 06/05 displays very good compatibility with various well-known producers.

Purpose

Recommended for water ballast tanks, cofferdams, void spaces, wet spaces, bilges, crude oil tanks, maintenance and repair or on-board maintenance.

Properties

Color: Black

Solids: 80 ± 2

Coverage: Theoretical Coverage: 3.20 sq. m/Lit at 250 microns dry / 312 microns wet

Thickness: 250 microns dry

Flashpoint: Flash Point: Mixed product > 32 °C

VOC: 228.00 g/Lit (material as into the container)

Application Data

Mixing Ratio: Basis 4 part per/volume, Curing Agent 1 part/volume

Thinner: Not recommended. The material is ready for use, under special conditions use Thinner for Epoxy PH 300, max 5% by volume.

Painting Method: Airless spraying is our recommendation, brush, and spray follows. Tip range 0.45mm-0.66mm (18-26 thou), blowing pressure shouldn’t be less than 190-246kg/cm2 (2700-3500psi). Thinner may be required. Use proper equipment. Actual safety measures and precautions are very important from the selected method and environment work. Emergency Contact Numbers are available world wide upon any request.

Cleaning: Power tool cleaning with Universal Thinner PH-400.

Readiness Time: 15 minutes in ample temperature

Pot Life: 3 hours at 5 °C, 90 min at 15 °C, 60 min at 30 °C

Curing Time: Within 4 days at 23°C (fully cured)

Drying and Over-Coating Conditions

PhilaTar PHE 0605.JPG

Coating Specification

If local temperatures are around freezing at a long overcoat period, proper selection of the systems, coating application procedures, proper surface preparation should be made as per actual existing film esp. over coated epoxy layer. Try to  the results of design factors, statements and specific recommendations test in a controlled laboratory. Always value the conditions and consult with Philadelphia Coatings LLC Technical Department.

Surface Preparation

All surfaces should be clean, dry and free from contamination. High pressure fresh water wash should be applied prior to the treatment or of the application. Steel products with mill scale: shot blasting or grit blasting should meet the requirements of Sa1 grade in Sweden derusting standard at least. Steel products without mill scale: to be ground by dynamic tools to meet the requirements of St3 grade in Sweden derusting standard. Steel products painted with plant primer: use slight grit blasting or dynamic tools to carry out secondary surface preparation to meet the requirements of St3 grade in Sweden derusting standard. For other surface treatments, please consult with Philadelphia Coatings LLC Technical Department.

Storage

Circa 18 months at 25°C, stored at dry, shaded and ventilated condition. The container/paint must be kept sealed and away from heat and ignition.

Pack Size

Basis 4 Gal. (16 Lit) drum, agent 1 Gal (3,785 Lit) drum. If other packing specifications are needed, please consult with Philadelphia Coatings LLC Technical Department.

Health and Safety

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.

Limitation of liability

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Philadelphia Coatings LLC. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, so Philadelphia Coatings LLC won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.

Disclaimer

The information in the product manual is based on our experiences from tests and practice. For the application without our knowledge, we could only make sure that our products themselves are warranted. We may modify the data in this product manual according to our continuous development and experience accumulation without advanced notice.