PHILATRIM PHE 06/01

A versatile high-performance epoxy coating       

Overview

A solventborne coating formulated for heavy-duty applications on vessels underwater and above water areas/hull, outside hull, cargo holds, decks, industrial environments, offshore platforms/oil gas asset and other. The resin system is enhanced for added resistance against water, abrasion and moderate chemicals. For use on interior and exterior concrete and metal steps and various other surfaces. For use at Newbuilding, Maintenance & Repair or On-Board Maintenance and various industrial constructions.

PhilaTrim PHE 06/01 displays very good compatibility with various well-known producers.

Purpose

·         Designed for heavy-duty applications

·         Outstanding resistance against water, oil, grease and moderate chemicals

·         Excellent wear and abrasion resistance

·         Suitable for interior and exterior concrete and metal surfaces

Properties

Sheen: Semi-Gloss

Color: Red Brown, Gray, Oxide Red, Green others as per RAL scale.

Weight Solids (%): 80 ± 2

Volume Solids (%): 58 ± 2

Theoretical Coverage: 100 sq ft/gal or 6.00-4.00 m2/Lit at 100-150 microns dry / 170-250 microns wet

Recommended Film Thickness: Over 250 microns dry by 2 coats.  

Weight per Gallon: 13.4 ± 0.5 lbs/gal

Viscosity: 88-98 KU

Specific Gravity: 1.40 g/Lit

Flashpoint: Mixed product > 90 °F (32°C)

VOC: 340.00 gr/Lit (2.8 lbs/gal) (material as into the container)

 

ASTM D412 for Elongation and Tensile Strength

ASTM D4060 for Abrasion Resistance

Application Data

Mixing Ratio: Basis 4 part per/volume, Curing Agent 1 part/volume.

Thinner: Not recommended. The material is ready for use, under special conditions use thinner PH 300 or PH 400, max 5% by volume.

Painting Method: Airless spraying is recommended, brush and spray follows. Tip range 0.48mm-0.66mm (21 thou), blowing pressure shouldn't be less than 141kg/cm2 (2000psi). Additional thinner may be required. Use the proper equipment. Actual safety measures and precautions are very important from the selected method and environment work. Emergency Contact Numbers are available World Wide upon request.

Cleaning: Power tool cleaning with Universal Thinner PH-400.

Readiness Time: 20 minutes in a proper temperature

Pot Life: 12 hours at 15°C, 8 hours at 23°C, 5 hours at 30°C

Curing Time: Within 4 days at 23 °C (fully cured)

Drying and Over-Coating Conditions

PhilaTrim.PNG

Coating Specification

Long overcoat period, if local climate, temperatures around to freezing point, proper selection of the systems, coating application procedures, proper surface preparation, as per actual existing film esp. over coated epoxy layer. Try to test design factors, statements and specific recommendations in a controlled laboratory. Always factor in the conditions and consult with Philadelphia Coatings LLC Technical Department before and throughout testing.

Surface Preparation

All surfaces should be clean, dry and free from contamination. High pressure fresh water wash should be applied prior to the treatment of the application. Steel products with mill scale: shot blasting or grit blasting should meet the requirements of Sa1 grade in Sweden derusting standard at least. Steel products without mill scale: to be grinded by dynamic tools to meet the requirements of St3 grade in Sweden derusting standard. Steel products painted with plant primer: use slight grit blasting or dynamic tools to carry out secondary surface preparation to meet the requirements of St3 grade in Sweden derusting standard. For other surface treatments, please consult with Philadelphia Coatings LLC.

Storage

Circa 24 months at 20°C, stored in a dry, shaded and ventilated condition. The container/paint, must be kept sealed and away from heat and ignition.

Pack Size

Basis 4 Gal. (16 Lit) drum, agent 1 Gal (3,785 Lit) drum. If other packing specifications are needed, please consult with Philadelphia Coatings LLC. Shipping weight: Basis 4 Gal. (16 Lit) 65.44 lb drum, agent 1 Gal (3,785 Lit) 4.2 lb drum.

Health and Safety

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read carefully and conform to precautions on MSDS and packing vessels. To avoid eye and skin contact, tools such as gloves, goggles and face mask etc. should be used during work with product (proper safety measures should be taken according to construction methods and circumstances). All work with the product must be carried out according to all relevant national health, safety and environment standards and codes. This product is for professional use only.

Limitation of liability

All information is given for guidance only and is subject to regional variation depending upon local climate and environmental condition. An excessive film thickness delays the final curing and creates sagging. Over coating interval will increase with the number of paint layers and the thickness of the paint film. For recommended paints at special circumstances, please consult with our Philadelphia Coatings LLC. Apply in good weather. The relative humidity must not exceed 80% temperature of the surface to be coated must be at least 3°C above the dew point. All data from the tests is obtained under lab conditions, so Philadelphia Coatings LLC won’t bear any liabilities from the condition whether the data could reflect the objective status of the actual application circumstance or not.

Disclaimer

The information in the product manual is based on our experiences from tests and practice. For the application without our knowledge, we could only make sure that our products themselves are warranted. We may modify the data in this product manual according to our continuous development and experience accumulation without advanced notice.